Monday, May 27, 2013
Pasting the car with his hands
Okleit car yourself - not in the cellar. To do this you than the film itself, it will take part assistant for a smooth installation of large sheets of film, as well as availability, pre-cooked, tools and some patience. Of the tools necessary to be reserved by: squeegee made of plastic or felt, with a knife or scissors, spray with water-detergent solution in a ratio of 1 / 10, White Spirit, hairdryer, mounting tape, dry cloth, masking tape. The film has a paper-based and applied on the surface of the car by using the mounting tape. In transferring the film on the surface of a car, it should be smooth squeegee. The main rule when pasting - is necessary to thoroughly clean and degrease the surface with white spirit. Other, no less important rule - pasting should be in place to avoid exposure to dust at room temperature for at least 10 degrees Celsius. Otherwise, defects will be formed. Pasting the car with his hands, is done using the stickers are already ready to use, offered for sale complete with mounting tape. Can also be ordered on their own in any agency on advertising. The procedure of gluing is as follows. 1. After a thorough bathing and drying cars, degreased surface with mineral spirits. 2. With the participation of an assistant to determine the location of the future location of vinyl film, it is necessary to make vinyl and using masking tape to keep the markup that will need to navigate when applied film. In this case, a vinyl film, yet, you can not remove the substrate and the mounting tape. Markings should be given maximum attention. It is also important to remember that the design surface irregularities are often the cause of defects in the pasting. 3. At this stage, you must carefully separate the base paper. The procedure is performed on a flat surface with an assistant. In this case, it should not samoskleivaniya film. The result is a vinyl film with a layer of mounting on it. 4. At this stage, spray, sprayed the place drawing plenty of stickers. It is important that a solution of soapy water flooded the entire surface, without exception. Such wet and soap, surface, allow to adjust the position of the label. Also, due to a slippery surface, it is convenient to expel air bubbles formed under the sticker. 5. Now, on the damp surface of vinyl and fits neatly smoothed squeegee. The air must push the squeegee from the center toward the edges of the film. In the presence of surface design bends, start priglazhivanie should be a central, flat parts, gradually moving to the edges. In the process of smoothing necessary to heat the sticker with a hair dryer. We can not allow the formation of folds and swelling of the film. Smoothing a section of the film, it is necessary at this point to separate the mounting tape. As a result, tension is removed stickers. If you have any wrinkles, it is necessary, carefully peel the section and smooth the back, heating the film dryer. In the field bends the surface, you need a little more heat and stretch the film during smoothing. If necessary, permitted, notching assembly layer, not touching the labels. If not possible exception of education folds, you can make an incision on the ground folds, thereby remove the tension throughout the film. 6. Upon completion of smoothing out the entire film, should be thoroughly dry everything with a hair dryer and make a 15 minute break. 7. When all dry, care must be taken to separate the mounting layer labels. Practical to separate the mounting layer, at an acute angle to the surface. 8. Using a squeegee made of felt, you must carefully conduct a further flattening of the label. Air bubbles, which remained under the label that did not get pushed squeegee, you can warm up a hairdryer, then pierce with a needle and smooth squeegee. Small bubbles will disappear over time, independently. Excess of the label must be trimmed. Edging stickers must be heated dryer and smoothed with bending. 9. Places treatment should be dried with a dry cloth or hair dryer. After all the manipulations, let the car "rest" during the day. During this time the label to bond with the surface. After this time, if necessary, we can go further squeegee made of felt. During the week, the car can not be washed.
